Radiant tube heating suits most large warehouses, because it warms people and surfaces directly rather than heating air that rises to the roof. Warm air units suit well-sealed buildings needing fast whole-space heat. Unit heaters suit spot and supplementary duty rather than whole-building heating. Hydronic systems suit long heating seasons but cost heavily to retrofit. Heat pumps suit moderate loads where cooling is also wanted. Electric radiant costs the most per kWh and suits occasional or off-grid use only.
The four factors that decide, before any appliance choice:
- Ceiling height
- Insulation level
- Door traffic
- Occupancy pattern
Stratification Is the Real Problem
Warm air rises. In a building with a 10-metre roof, heated air collects above head height and stays there, leaving the floor cold while the roof space sits warm.
That is why a heater’s headline efficiency means little on its own. A 95% efficient unit delivering heat to the roof void is wasting more than an 80% efficient system delivering it to the floor, and a cold pick face slows warehouse picking speed and accuracy regardless of what the roof-level thermostat reads.
Two consequences follow:
- Running costs depend more on controls and stratification than on the appliance. Zoned time and temperature control plus destratification usually beat an appliance upgrade.
- Radiant systems stratify far less than warm air, because they heat surfaces rather than the air itself.
Measure the roof-to-floor temperature gradient before specifying anything. A steep gradient indicates the existing system is heating the wrong part of the building.
Radiant Tube Heating
The default recommendation for the main volume of a large warehouse.
Radiant tube heaters warm people, floors, racking and stock directly through infrared, rather than warming the air. Heat does not rise away from the working area, and the floor slab retains warmth.
It suits:
- Tall buildings where warm air would stratify
- Draughty buildings with frequent door openings
- Sparsely occupied spaces where heating the whole air volume wastes energy
The trade-off: it warms up slowly, since surfaces take time to absorb heat. Once at temperature it holds a working level well, so it suits continuous operation better than intermittent use.
Warm Air Units
The right choice where the building is well sealed and needs fast heat across the whole space.
Warm air systems are flexible on fuel and can be zoned, which matters in buildings with distinct areas running different schedules.
They suit well-insulated buildings with limited door traffic and consistent occupancy.
They require destratification fans at any significant ceiling height. Without them, the heated air they produce ends up where nobody works, and the system runs constantly chasing a floor-level thermostat it cannot satisfy.
Unit Heaters
Unit heaters suit spot heating and supplementary duty rather than whole-building heating.
Appropriate uses:
- A packing bench or inspection station within an otherwise unheated space
- A goods-in area needing warmth only during deliveries
- Supplementary heat in a cold corner the main system does not reach
Specifying unit heaters as a building’s primary system is a common and expensive mistake, because the output needed to heat a large volume through point sources exceeds what the approach is designed for.
Hydronic Systems
Boiler-fed hydronic heating suits long, steady heating seasons and mixed-use buildings combining warehouse space with offices.
The limitation is retrofit cost. Installing pipework, a plant room and emitters in an existing building is substantially more expensive than suspended heaters, which is why hydronic usually appears in new build or major refurbishment rather than as a replacement system.
Heat Pumps
Heat pumps suit moderate loads where cooling is also wanted, which makes them more relevant to mixed-use and temperature-controlled facilities than to general storage.
The constraint is cold weather. Output falls as outside temperature drops, so a supplementary heat source is commonly added for the coldest periods. Specify the supplementary source at design stage rather than discovering the need in the first hard winter.
Electric Radiant & Quartz
Running cost per kWh is the highest of all the options, which confines these to specific situations.
They suit off-grid locations, genuinely occasional use, and spot heating a single workstation. They do not suit heating a building.
Destratification Fans
Where warm air heating is used at height, destratification fans are not optional.
They push the warm air collected at roof level back down to the working area, which both raises floor temperature and lets the system cycle off sooner.
Two points on specification:
- They matter most where the gradient is steepest, so measure before deciding how many and where
- They still help in very tall radiant-heated buildings with mixed heat sources, though the benefit is smaller than with warm air
The Cheapest Improvement Is Usually the Doors
High-speed doors and air curtains at loading bays are often the cheapest heating improvement available, and they are frequently overlooked in favour of appliance upgrades.
A dock door standing open during loading vents the heated volume of the building continuously. No heating system compensates economically for an open door.
Address in this order:
- High-speed or rapid-close dock doors, reducing the time each opening stays open
- Air curtains at doors that must stay open during operations
- Dock seals and shelters, sealing the gap between trailer and building
- Roof and wall insulation, where the building envelope is poor
- Only then the heating appliance itself
Choosing a System
For most large warehouses, including contracted warehousing services London sites, a workable combination is radiant tube heating for the main volume, warm air or unit heaters for offices and mess areas, and destratification fans wherever warm air is used at height.
Survey the building before committing. Two similar warehouses can need different solutions depending on insulation, door traffic and how the space is actually occupied through the day, which is one reason renting warehousing services Birmingham removes the capital question entirely.
Specify zoned time and temperature control regardless of appliance. Heating an entire building to a uniform temperature when only part of it is occupied is the largest avoidable cost in most warehouse heating systems.
Frequently Asked Questions
What temperature should a warehouse be?
Workplace minimum temperature requirements vary by jurisdiction, and stock requirements may set a separate standard, particularly on order fulfilment London contracts holding temperature-sensitive lines. Check the applicable regulations for your country alongside any product storage specifications.
Is radiant or warm air heating cheaper to run in a warehouse?
Radiant usually costs less in tall or draughty buildings because heat reaches the floor rather than the roof. Warm air can compete in well-sealed, lower buildings with destratification fitted.
Do destratification fans save money?
They reduce energy use wherever a significant roof-to-floor temperature gradient exists, by returning heated air to the working area and letting the heating cycle off sooner.
Can you heat only part of a warehouse?
Yes, through zoning and radiant heating directed at occupied areas. Radiant suits this better than warm air, which heats the whole air volume regardless of where people are.
Does insulation matter more than the heating system?
In a poorly sealed building, yes. Door controls and envelope improvements often deliver more than an appliance upgrade, which is why a survey should precede any specification.
